Fused Dichroic Bedazzled Earrings Free Fuseworks Project Guide

Item #: FPG0020F

You must be logged in with an active account to see prices and availability.

Only qualified resellers can register for an account.


Free Fusing Project Guide

Fuseworks™ Kiln

Fuseworks™ Earring wires


Westrim™ pearl assortment
Sterling Silver-Plated Square Cabochon Mini Links
2 hat pins
Fuseworks™ Earring wires
Fuseworks™  Bits and Pieces - Dichroic
Fuseworks™  Bits and Pieces – The Basics
Fuseworks™ Kiln
Fuseworks™ Kiln Paper
Fuseworks™ Glass Cutter
Studio Pro™ Running Pliers
Jennifer’s Mosaics™ Wheeled Glass Nippers
Chain-nose pliers
Round-nose pliers
Project Tips
This project can be made from scrap glass.
Do NOT use a self-lubricating style cutter with oil while cutting glass. Oil of any kind on the surface of the glass may mar your glass or cause breakage when fired.
Always read and follow kiln safety instructions.
Always wear safety glass when working with glass crafting tools.
FUSING GLUE RECIPE: 1 drop of Elmer’s school glue to 3 drops water,
mix thoroughly.
1. Place white glass on a clean flat cutting surface with the smooth facing up.
2. Start on an edge of the glass, holding the cutter firmly in one hand; push the cutter gently and evenly across the glass. Decrease pressure slightly as you reach the opposite edge of the glass; lift the cutter off the glass at the end.
3. Hold the glass in one hand, with the score facing up. With the other hand, center the score line in the jaws of the running pliers about a half inch onto the glass surface. Apply pressure to the handles; until the score runs and the glass separates into two pieces.
4. Cut two ½” x ½” square from the white glass.
5. Next, select a desired dichroic glass color, this project uses dichroic spiral violet and dichroic green and nip 2 pieces from each color using a wheeled glass nippers. Dichroic pieces can be random in shape but two must fit on the ½” x ½” surface of the white glass with at least 1/8” between them.
6. After cutting glass to the desired shape, clean and dry with a lint-free cloth. If using fusing glue to hold your glass project in place, make sure the glue is completely dry before firing.
7. Cut a square of kiln paper to fit the base of the Fuseworks™ Microwave Kiln. Place paper on the kiln base.
8. Arrange each ½” white square on top of kiln paper ½” apart. Place the dichroic pieces on top as desired.
9. Carefully place kiln base with glass in the center of microwave oven. Place lid on top of the base. If using fusing glue to hold the dichroic pieces in place make sure the glue has dried thoroughly before placing glass in the microwave.
10. To achieve a tack fuse, use a 1200 WATT microwave and set temperature at 80% power for 2 minutes, then on high for 30 seconds. PLEASE NOTE: Every microwave oven and kiln will vary. If using a microwave with a lower wattage keep the time consistent but increase the power.
11. When microwave time has expired, use heat resistant gloves or mitts to carefully open the lid. Glass should be slightly rounded but still maintain it shape and integrity. If the glass is not fused to your liking, return kiln lid to the base and place in microwave for 20 second intervals until piece is fused. Never touch the glass. HOT TIP! HOT glass looks like COLD glass, BE CAREFUL!
12. When desired results have been achieved, using heat resistant gloves, remove the kiln from the microwave oven. Set on a heat resistant work surface and allow to cool for 30-45 minutes. Do not leave the lid off the kiln for an extended period of time during this stage. Removing the lid may cause your glass to crack.  
13. Once the glass has cooled completely, remove the fiber paper from the back of the
fused project by rubbing the surface with a wet paper towel or cleaning the project under warm water.
14. Use E6000 glue and adhere each piece of glass to the front of a silver-plated square cabochon mini link and allow drying.
15. While the glue dries, thread pearls onto a head pin. Using a chain-nose pliers, bend wire over the pliers to a 90 degree angle. Next, grasp the head pin with a round-nose pliers, pull the wire up and over the top of the round nose pliers to form a full loop. Nip the long end of the wire with a wire nipper to form a loop. Open the loop and thread one end of the Cabochon on to the loop and press to close.
16. Attach the earring wires to the top of the cabochon using this same method.
17. Enjoy!



No reviews have been written for this product.