Fused Glass Flip Flop Embellished Invite Project Guide


  • Free Fusing Project Guide
  • Fuseworks™ Kiln
  • Fuseworks™ Glass Cutter
Find a Store
Materials - Card
Golden Yellow, Mint Green, Periwinkle and Hot Pink Card Stock
DCWV, “The Stack 5” (sand print paper)
Pop Dots™Stampin’ Up! ™
Flower Punch Stampin’ Up! ™
1” Circle Punch Stampin’ Up! ™
Polka Dot Punches Stamp Set Stampin’ Up! ™
Orange Ink Stampin’ Up! ™
Ultra Fine Green Glitter Stampin’ Up! ™
Scalloped Stencil
Hot Glue
Glue stick
Materials – Flip Flop Pin
Fuseworks™ 2”x3” Variety Sheet Glass – Warm Colors
Fuseworks™ Bits and Pieces – Cool Colors
Fuseworks™ Kiln
Kiln Paper
Fuseworks™ Glass Cutter
Fuseworks™ Lightweight Running Pliers
Pin Back
Project Tips
Wear safety glasses when using glass-crafting tools.
Always read and follow kiln safety rules and warnings.
Card Instructions
1. Use orange ink with the Stampin’ Up!™ Polka-Dot Punches Stamp Set and stamp one side of golden yellow card stock. Cut card stock into a 5 ½”x 11” rectangle; score and fold in half.
2. Using a Stampin’ Up!™ 1” circle punch, punch two circles from mint green
card stock.
3. Next, cut a 4” x 6” rectangle from hot pink card stock. Use a small scallop stencil to create a scalloped edge around the perimeter of the rectangle.
4. Using a Stampin’ Up!™ flower punch cut two flowers from periwinkle card stock.
5. Cut a 2 ½” x 3” rectangle from sand print paper.
6. Center the scalloped edged hot pink paper on top of folded yellow paper. Glue into place with a glue stick.
7. Measure one inch down from the top of the scalloped edge of the hot pink card stock and lightly draw a 2 ¼” x 2” rectangle. Open the card and lay flat. Use a craft knife and cut an opening along the outline of the rectangle. This will create a window in the front of the card.
8. Glue the sand printed paper to the inside of the card so that it appears centered inside the window.
9. Place a dollop of hot glue in the center of the mint green circles and sprinkle with ultra fine green glitter, cool and dry.
10. To assemble flower, adhere a mint green circle to the center of the periwinkle flower, using a Stampin’ Up!™ Pop Dot™, make two.
11. Apply assembled flowers to the card with Pop Dots™ just below the window.  
Flip Flop Instructions
1. Make photocopies of the patterns in the downloadable PDF. Using scissors, cut-out pattern pieces, staying on the inside of the pattern outline.
2. Place pattern pieces on the colored sheet glass indicated above (FIG. 1). Trace around the outside edge of the pattern using a Sharpie® Marker.
3. To cut glass, start at one edge of the glass; place the cutter perpendicular to the glass. Glass likes to be cut from edge to edge. Apply consistent medium pressure and push the cutter across the glass, following the pattern line to the opposite glass edge, this is called a score. A good score appears as a continuous scratch on the surface. Break/run score with running pliers. Continue to score and break the glass until the pattern is completely cut. Clean glass using paper towel moistened with water. Completely dry the surface of the glass with a lint free cloth.
4. Next, cut a 2” X 2” piece of kiln paper. Remove the lid from the Fuseworks™ Kiln. Place the kiln paper on the kiln base.
5. Layer the glass on the kiln paper. Place the transparent yellow on kiln paper first; embellish with the blue opalescent glass to create the flip flop straps (FIG. 2).
6. Carefully set the base with glass inside the microwave. Cover with kiln lid.
7. Fuse using the chart below. PLEASE NOTE: All microwave and kiln combinations will have different firing patterns. Be sure to take careful notes and log all fusing times for future use.
8. After time is up, open microwave and, using Hot Mitts, carefully lift the lid enough to inspect the fusing process. Add additional time in 30 second increments until desired results are achieved.
9. Remove kiln from microwave using the Hot Mitts and place on a heat resistant surface. Cool the kiln for at least 30 minutes WITHOUT REMOVING LID. PLEASE NOTE: Removing the lid or peeking under the lid during the cooling will result in your piece cracking. Glass remains hot for a long time and should be handled with great caution.
10. Once cooled, use E6000 to glue a pin back on the back side and allow it to try per the manufacturer’s recommendations.
11. Place the pin in the window of the card, mark with a pencil and use a safety pin to create two holes for the pin back to go through. 

Sign up for projects