Karma Drawer Pull

Item #: PROJECT0368

You must be logged in with an active account to see prices and availability.

Only qualified resellers can register for an account.

Features

Fuseworks™


Description

Karma Drawer Pull
BY: Jeanne Baruth
SKILL LEVEL: 1 (1 being the easiest, 5 being most difficult)
 TIME TO COMPLETE: 3 hours
→PROJECT TIP
• Wear safety glasses when glass-crafting.
• Always read and follow kiln safety rules and warnings.

 MATERIALS CHECKLIST
• Fuseworks™ Microwave Kiln
• Fuseworks™ Hot Mitts
• Fuseworks™ Kiln Paper
• Fuseworks™ Fusible Shapes Black (1) and Dichroic Blue (1)
• Fuseworks™ Fuse Art™ Decals The Orient – Bamboo
• Fuseworks™ Fuse Art™ Decals Word Art - Karma
• Fuseworks™ Round Drawer Pull
• Safety Glasses
• E-6000®
• Scissors
• Bowl for water
• Microwave
INSTRUCTIONS
1. Clean glass using paper towel moistened with water. Completely dry the surface of the glass with a lint-free cloth.
2. Cut a 2” X 2” piece of kiln paper. Remove the lid from the Fuseworks™ Kiln. Place the kiln paper on the kiln base.
3. Position the black Fusible Shape in the center of the kiln paper and cover with a blue dichroic Fusible Shape.
4. Carefully set the base with glass inside the microwave and cover with kiln lid. Fuse in a 1200-watt microwave at 50% for 2 minutes; 80% at 1 minute; 30 seconds. If using a microwave with a lower wattage, increase the power percentage but keep time consistent. PLEASE NOTE: All microwave and kiln combinations will have different firing patterns. Be sure to take careful notes and log all fusing times for future use.
5. After time has expired, open microwave and, using Hot Mitts, carefully lift the lid enough to inspect the fusing process. The glass is fused when the edges are nicely rounded. If necessary, continue to microwave at 15-second increments until desired results are achieved. 6. Remove kiln from microwave using the Hot Mitts and place on a heat-resistant surface. Cool the kiln for at least 30 minutes WITH THE LID ON. CAUTION: Removing the lid or peeking under the lid during the cooling stage may result in your piece cracking. Glass remains hot for a long time handle with great care.
7. When glass has completely cooled, remove from kiln and place on your work surface.
8. Cut out the “bamboo” and “karma” decals and place them in a bowl of water (preferably distilled) for approximately 30 seconds. Using the photo as a guide, apply decals by sliding the backing-paper away from the decal so the decal rests against the glass. The decal should slide off backing-paper easily; if not, let it soak longer. Use a paper towel to pat the moisture from the decal and glass. Should air bubbles appear, push them out with your finger. Allow them to dry completely.
9. Remove the lid from the Fuseworks™ Kiln and discard used kiln paper. Cut a 2” X 2” piece of kiln paper and place on the kiln base.
10. Place the glass with the decal face up in the center of the kiln paper.
11. Carefully set the base with glass inside the microwave. Cover base and glass with kiln lid.
12. If using a 1200-watt microwave, fuse at 50% power for 2 minutes. Heat again, at 80% for 1 minute and 30 seconds. If using a microwave with a lower wattage, increase the time to 2 minutes and 30 seconds. PLEASE NOTE: All microwave and kiln combinations will have different firing patterns. Be sure to take careful notes and log all fusing times for future use.
13. When time has expired, open microwave and, using Hot Mitts, carefully lift the lid enough to inspect the fusing process. Check your glass, if the decal appears as a white silhouette; continue fusing at 100%, adding an additional 15 seconds to the time until the decal looses the white appearance. When you are able to see the color and definition of the decal, the fusing process is complete. Remove kiln from microwave using the Hot Mitts and place on a heat-resistant surface. Cool the kiln on a heat resistant surface for at least 30 to 40 minutes WITH THE LID ON. CAUTION: Removing the lid or peeking under the lid during the cooling will result in your piece cracking. Glass remains hot for a long time handle with great caution. Cool the glass completely.
14. Once cooled, glue the glass to the center of the drawer pull. Allow it to dry before using.
15. Follow draw pull instructions for installing.

Reviews

No reviews have been written for this product.