DIY Holiday Krafty Block

Item #: FPG0007K

You must be logged in with an active account to see prices and availability.

Only qualified resellers can register for an account.

Features

KraftyBlok™ Rectangle

Square KraftyBlok™ Minis

Large KraftyBlok™ Original

Large KraftyBlok™ Stand

LED Lights


Description

KraftyBlok Christmas Projects

 
Project 1: Let’s Be Merry Block
 
Materials
One KraftyBlok™ Rectangle
One 5-inch Strand of LED Lights
5-inch Strand of Small Festive Garland
4-6 Small Ornaments
One Festive Vinyl “Let’s Be Merry” Sticker or a sticker of your choice.
Decorative Ribbon
Scissors
Optional: Extension Cord
 
Be Safe!
- Use a strand of LED lights instead of regular Christmas Lights. They are much safer and produce less heat.
Let’s get started
1. Wrap garland around the strand of LED lights.
2. Insert lights and small ornaments inside block
3. Cut a slit in the stopper from edge to center hole.
4. Slide the light cord through the slit, then close block with stopper.
5. Place your choice of decorative sticker on the center front of block.
6. Wrap a decorative ribbon around block and finish with a bow on top.
7. Plug it in and enjoy!
 

Project 2: Joy Blocks
 
Materials
Three Square KraftyBlok™ Minis
Three 5-inch Strand of LED Lights
20x20-inch of Festive Snow Blanket (You will cut 3 pieces into 6X6)
Large Glittery Letter Stickers
Christmas Character Stickers
Decorative Ribbon
Scissors
Pencil
Optional: Extension Cord
 
Be Safe!
- Use a strand of LED lights instead of regular Christmas Lights. They are much safer and produce less heat.
Let’s get started
1. Lay the block face down and insert a sheet of 6x6-inch snow blanket in side. Make sure it is lying flat.
2. Carefully insert a 5ft strand of LED lights. If the blanket shifts, just used a pencil to readjust.
3. Cut a slit in the stopper from edge to center hole.
4. Slide the light cord through the slit, then close block with stopper.
5. Place coordinating letter on the block and your choice of character sticker.
6. Wrap a decorative ribbon around block and finish with a bow on top.
7. Repeat this process for the next two blocks. All three blocks together should read “JOY”.
8. Connect all the blocks together to light up.
10. Display on a fireplace mantel or under the Christmas Tree and enjoy!
 
 

Project 3: The Family Picture Block 
Materials
One Large KraftyBlok™ Original
One Large KraftyBlok™ Stand
Multi Colored LED Slim Wire Garland Lights with on and off switch
5x6 Family Photo
Festive Snow Blanket
Large Decorative Ribbon
Small Red Ribbon
Acrylic Paint and Small Paint Brush
Small Decorative Ornaments
One Rectangle Floral Foam
Three Small Sizes of Round Floral Foam
2mm Bendable Wire
Wire Cutters
Scissors
 Tape
Small Tongs
Hot Glue Gun with Glue Sticks
Pencil

 
Be Safe!
- Use a strand of LED lights instead of regular Christmas Lights. They are much safer and produce less heat.
Let’s get started
1. Measure the base of your block and cut your rectangle foam to those exact measurements. You might have to cut in half to fit in opening.
2. Wrap up your rectangle foam piece in snow blanket and lay at the bottom of the block. Tuck in the sides with a pencil.
3. For the snowmen double check the Floral Foam Rounds can fit through the opening. If not, simply cut in half.
4. Decorate your snowmen by painting a face and buttons on the body. Set aside and let it dry.
Optional: You can also make a cute scarf or hat for your snowmen using small red ribbon and hot glue it in place.
5. Next cut two pieces of wire. One 3-inches and the other 4-inches. The 3-inch wire will be for the small snowman and the 4-ich wire will be for the larger snowman.
6. Insert both wires onto both ends of the rectangle foam base at the bottom of the block. Use small pliers for a better reach.
7. Then assemble your snowmen onto their designated wire. First the body then the head. You can also use your small tongs for this part for easy reach.
8. Next insert your family picture. Make sure the back of the picture is laying flat against the block. You can tape down for security if you like.
9. Place your Multi Colored LED Slim Wire Garland Lights inside your block. Make sure to keep the on and off switch outside of block.
10. Adorn the inside of block with small festive ornaments
11. Wrap a decorative ribbon around your block and finish with a bow on top
12. Place block inside our Large KraftyBlok™ Stand
13. Place your family picture block anywhere you please to show off your amazing creativity!
 
 
All Done!
 
These are a great way to decorate your home for the holidays and they also make great gifts!
 

Specifications

Lets Be Merry
One KraftyBlok™ Rectangle
One 5-inch Strand of LED Lights
5-inch Strand of Small Festive Garland
4-6 Small Ornaments
One Festive Vinyl “Let’s Be Merry” Sticker or a sticker of your choice.
Decorative Ribbon
Scissors
Optional: Extension Cord


Joy Blocks
Three Square KraftyBlok™ Minis
Three 5-inch Strand of LED Lights
20x20-inch of Festive Snow Blanket (You will cut 3 pieces into 6X6)
Large Glittery Letter Stickers
Christmas Character Stickers
Decorative Ribbon
Scissors
Pencil
Optional: Extension Cord


The Family Picture Block
One Large KraftyBlok™ Original
One Large KraftyBlok™ Stand
Multi Colored LED Slim Wire Garland Lights with on and off switch
5x6 Family Photo
Festive Snow Blanket
Large Decorative Ribbon
Small Red Ribbon
Acrylic Paint and Small Paint Brush
Small Decorative Ornaments
One Rectangle Floral Foam
Three Small Sizes of Round Floral Foam
2mm Bendable Wire
Wire Cutters
Scissors
Tape
Small Tongs
Hot Glue Gun with Glue Sticks
Pencil

Reviews

No reviews have been written for this product.